Summary of Como usar FLUKE DSX-8000 Y 5000

00:00:00 - 00:20:00

This video shows how to use the FLUKE DSX-8000 Y 5000 cable tester to test cable connections and diagnose electrical problems. The user is shown how to connect the cable to the adaptors, how to check the connection on both sides, and how to use the analyzer to see the distance the problem is occurring. The user is also shown how to create a new project and to pass the information from the equipment to Win Work, the software used for the report.

• 00:00:00 This video explains how to use the FLUKE DSX-8000 Y 5000 cable tester to test cable connections in the 5e and 5b categories. The equipment includes a zinc body, bercy module, and copper cable. The presenter demonstrates how to use the equipment to test connections in the 5e, 5b, 4, and 8 categories. The kit comes with two adapters for making permanent links, a micro USB audio output, and a 15-volt input for charging the equipment. The presenter then shows how to configure the equipment and test the cable connections.
• 00:05:00 This video shows how to use the FLUKE DSX-8000 Y 5000 testing equipment to certify cable connections. The user is also shown how to assign an operator, create a new project, and modify an existing project. Finally, the user creates a new test project. If a project already exists, the user can switch to editing mode and edit the project. If a new project is desired, the user enters project information and creates a new project. The user then selects a cable type and test protocol. The test project is then saved and a new cable type is generated. The user then selects a cable manufacturer and creates a new cable manufacturer. The user then enters cable data and creates a new cable. The user then tests the cable and enters results.
• 00:10:00 This YouTube video shows how to use the FLUKE DSX-8000 Y 5000 tester to test cable connections. The tester is said to be a 69% accurate, but it can still test cable category 5 according to the manufacturer. In order to test the cable, the tester needs a reference. The user creates a primary reference by connecting the tester to their remote and mail. They then connect a link and test the cable. Finally, they disconnect the link and test the cable again. This process is repeated for each cable in the test. After testing all cables, the user creates a report and compares it to the manufacturer's information. They then test a cable with a new operator, christian. christian tests the cable and the tester reports that the connection is passing in the remote, and that the test is successful in the main window. Next, they connect a second cable and test the connection. The user then tests a cable with a known good reference. They finish the video by testing a cable with a bad reference.
• 00:15:00 This video demonstrates how to use the FLUKE DSX-8000 Y 5000 cable tester. First, the user connects the cable to both the adaptors for channels and then performs a test channel. The cable tester then verifies that all is correct and then tests a channel on category 5. The cable is then certified and the results displayed on the remote. The tests were done on the same cable that was used for the triple-A diagnostic. The next test is to create a test for a cable that the user has created, called the Vertical Cable. The cable tester tests the cable for quality and then shows the user how to expand the pairs and see according to line. The results are very close to the limit. The next test is to connect a cable that is known to be incorrect and see if the DSX-8000 Y 5000 can identify the problem. The DSX-8000 Y 5000 can generate a map of the incorrect cable.
• 00:20:00 The FLUKE DSX-8000 Y 5000 can be used to diagnose and repair electrical systems. First, orient yourself according to the instructions. Next, connect the pin to the board as shown. Then, check the connection on both sides. If we proceed, the diagnostic tool will show us the same thing again. However, in the diagnosis that you saw earlier, we will be able to use the analyzer to see the distance the problem is occurring and which of the parents' pins it is. We can then select the correct pole using the primary color and the non-affected parent's pin. The analyzer does not help much because we will be able to fix the problem later and leave this information stored. However, at the moment we cannot solve it, and we know that the cable's cable and pin 02 have a problem. We have a project underway that involves replacing a cable's 0 1 and 0 2 wires. In this video, we will learn how to complete the certification process and create a project different than cable wiring. Finally, we will see how to pass the information from our equipment to Win Work, the software used for the report.