Summary of CURSO SPLITS YORK INVERTER TEORIC02

00:00:00 - 00:30:00

This video discusses the importance of properly installing and maintaining a split York inverter. It covers topics such as taking measurements, installing the evaporator, and checking the water flow from the condenser. The video also emphasizes the importance of leaving a space of at least 2 meters between the condenser and other equipment.

• 00:00:00 In this video, a detail is shown with code failures in some of our manuals and they come and if not in the manual for service, they do. I recommend that manuals not be thrown away, but if they have any experience, they should read the English editions that come with the equipment. It doesn't matter which day we learn English, we're going to understand each other, but I'll tell you one thing very, very important. If we don't have that worry about the minimums we lose, we'll end up with lots of problems. And we won't even do that--we're just as bad as they say because the whole team comes complete because that's why we're concerned about putting manuals in place so that tomorrow, past, or even in some of the equipment's manuals, service centers come. But sometimes we also get those manuals and we throw them away because we don't know who to turn to. I tell them and no, no, no it's not in the form of bothering them. Simply, we have to give each thing its importance now that it comes on the equipment. Sometimes this says, "This isn't useful," so we'll throw it away, but it's important that we pay attention to each thing that
• 00:05:00 In this video, the presenter explains how to install a split York inverter. First, they need to leave at least 15 cm between the point of minimum and the point of maximum. Then, they need to decide where the minimum distance is, based on the type of wall they are attached to. If they are too close to the wall, they might as well leave it at 15 cm. This is because, often, they attach the inverter too high up on the wall, which can cause it to fall off. They also need to leave enough space at the minimum distance, so that when they do service the inverter, they can remove the front decorative part without having to damage the appliance. If they are installing a new inverter, they need to be sure to use the special hours package for wall rock. If they are not sure what package they need, they can consult a technician. Finally, they check to make sure that the inverter is installed at the correct level, and then they start to check the distance between the inverter and the water tank. Next, they check the distance between the inverter and the lower wall, where the refrigerant and condensate pipes will be installed. They also need to make sure that the lower wall
• 00:10:00 This video discusses how to safely disconnect an electrónico that has been broken many times. We often don't notice and the first thing we say is "I don't do it because it'll lose warranty." What's happening is that they don't want to spend time reviewing what happened or what is currently happening because sometimes it can be easy to mistakenly think that a fuse wasn't installed properly or that a cable was not properly installed. Sometimes things just happen and we don't know how to fix them. In this video, we are seeing the components of a control system. This includes the connection to the control unit and the display. We will also be checking the temperature we want the machine to work at. Finally, we will be looking at the sensor that monitors the condition of the fourth circuit. All of these components are located on the same board. Jordi then goes over the manual for service. This includes a 97-page booklet for each machine.
• 00:15:00 In this video, the instructor explains how to properly install an inverter teor- ic unit in a wall. The unit is used to create a niche in the wall, and there is an outlet on the back of the unit for attaching a power cord. The instructor goes on to say that, in most cases, the evaporator will be placed on this side of the unit. Once the evaporator is properly installed and hooked up, the instructor demonstrates how to check the water flow from the evaporator and the condenser. The final point made in the video is that it is important to check the water flow from the condenser before you start working on the installation, in order to avoid any surprises.
• 00:20:00 The video demonstrates how to properly install an inverter. It covers important tips, such as taking measurements, and ensuring all screws are tight. The final step is to install the front decorating piece.
• 00:25:00 The video discusses the importance of inspecting pressure readings in order to determine if there is a problem with the compressor. It goes on to say that, in addition to checking the amperage, it is also important to check the space around the condenser. If this space is not maintained at a minimum of 2 meters, the compressor will eventually be tronned. Another important point made in the video is that, when installing a condenser, it is always important to leave a space of at least 2 meters between the condenser and the other equipment. This is to prevent the equipment from being over-protected and eventually damaged. Finally, the video discusses the importance of always having two keys on hand in order to make a good compressor grip. This is because, if only one key is used, the compressor may not be adequately tightened.
• 00:30:00 The video discusses how a split York inverter can lose efficiency and capacity over time.