Summary of How to Install and Connect a Next-Generation LiftMaster Belt Drive Garage Door Opener

00:00:00 - 00:20:00

The video explains how to install and connect a Next-Generation LiftMaster Belt Drive Garage Door Opener. The opener comes pre-installed with safety reversing sensors, which are to be mounted on each side of the garage door at floor level. The safety reversing sensors are to be installed no more than six inches from the floor. The video also covers how to program the garage door opener's travel limits.

• 00:00:00 This video demonstrates how to install and connect a Next-Generation LiftMaster belt drive garage door opener. You will need to have your homeowner's cell phone or mobile device available on the day of installation, the password for their wi-fi network, the last five digits of your dealer external id, and the keypad of the garage door opener. You will also need the rail assemblies, the safety reversing sensors, the header bracket, the mounting bracket, the control panel, the remote controls, the sprocket cover, the battery, the hardware bag, and the user guide. Be sure to leave the user guide for the homeowner to open. Before assembly, cut off the zip ties and place the garage door opener about 10 feet away from the garage door. Assembly of the rail assembly consists of placing the t-rail with the belt and trolley already included on top of packing material, attaching the rail to the motor unit, and tightening the bolts. Hand-tighten the bolts, do not use power tools.
• 00:05:00 This video demonstrates how to install and connect a Next-Generation LiftMaster belt drive garage door opener. The belt is wrapped around the sprocket, the threaded bolt is inserted through the trolley, the belt is secured in place with the spring trolley nut, and the assembly is completed by installing the sprocket cover. The header bracket is centered over the garage door and fastened to a structural support, and if a properly installed support bracket is not already in place, you must supply one along with the hardware for fastening it to the structural supports. The hanging brackets and hardware for connecting the garage door opener to the support bracket are also shown. Measure and cut the hanging bracket, connect the hanging bracket to the garage door opener and the support bracket, remove the 2x4 and lower the garage door, make sure the emergency release rope is tied in a secure knot through the handle, install the emergency release rope to the trolley making sure the handle is at least six feet off the ground, cut off the excess rope, and carefully melt the end to prevent fraying. Finally, if the garage door is made of lightweight material, make sure both horizontal and vertical reinforcements are installed before attaching the door bracket.
• 00:10:00 This video demonstrates how to install and connect a Next-Generation LiftMaster Belt Drive Garage Door Opener. The opener comes pre-installed with safety reversing sensors, which are to be mounted on each side of the garage door at floor level. The safety reversing sensors are to be installed no more than six inches from the floor. The video also covers how to program the garage door opener's travel limits.
• 00:15:00 The video explains how to install and connect a Next-Generation LiftMaster Belt Drive Garage Door Opener. The travel limits have not been set, but you will need to restart the process again if the product does not have the step saver setup label. To prevent damage to vehicles, be sure the fully open door provides adequate clearance. Once the door is in the fully open position, press and release the adjustment button the garage door opener lights will flash twice and the down button will start flashing. Now press and hold the down button until the door is in the desired down or closed position. Once the door reaches the correct closed position, press and release the adjustment button the garage door opener lights will flash twice and the up button will begin to flash. Now press and release the up button when the door travels to the open position the down button will begin to flash. Press and release the down button the door will travel to the closed position. Programming the travel for your garage opener is now complete. Anytime you make any adjustments, the safety reversal system must be tested to test the protector system. To test the safety reversal system open the garage door place an object that is at least 12 inches high such as a box in the path of the garage door so that it
• 00:20:00 The video demonstrates how to install and connect a Next-Generation LiftMaster Belt Drive Garage Door Opener. The steps involved include turning on wi-fi and bluetooth on the mobile device, enabling location services on the mobile device, and installing the myq app. Once the app connects to the device, a list of available networks will appear. The homeowner's home network will be selected and entered the network password. The garage door opener will beep three times, and the connection will be successful. The homeowner can now control the garage door opener using my cue from their mobile device. Finally, a digital sticker will be created and sent to the homeowner's dealer.